Pumping lug

Shore angling - everything welcome! The opinions expressed here are those of the private individuals and we accept no responsibility or liability.

Moderator: donal domeney

Pumping lug

Postby Thompst111 » Thu Nov 07, 2019 9:48 am

Alright lads. So mate just made a bait pump had a go yesterday works lovely just wanting info or anywhere north county Dublin that has a decent amount of lug
Thompst111
SAI Bait Ball
 
Posts: 108
Joined: Fri Jan 04, 2019 10:12 pm
Has thanked: 4 times
Have thanks: 18 times

Re: Pumping lug

Postby ste c » Thu Nov 07, 2019 5:37 pm

Place is destroyed not alot of decent lug beds left most lads that pump do it on the big low tides
User avatar
ste c
SAI Megalodon!
 
Posts: 1404
Images: 21
Joined: Sat Apr 17, 2010 6:01 pm
Location: dublin
Has thanked: 3 times
Have thanks: 323 times

Re: Pumping lug

Postby Thompst111 » Thu Nov 07, 2019 9:28 pm

Gave barnageara a quick go yesterday not many about 15 in an hour. Gonna give rogerstown a go tomorrow hopefully pays off
Thompst111
SAI Bait Ball
 
Posts: 108
Joined: Fri Jan 04, 2019 10:12 pm
Has thanked: 4 times
Have thanks: 18 times

Re: Pumping lug

Postby kieran » Thu Nov 07, 2019 10:59 pm

north shore of malahide between the golf course and the railway bridge used to be where we went, but that's 20 years ago.
strand road from sutton out towards red rock used to have lug and was good for maddies too
you should also check out the small harbours - lusk etc. - at low water as they can have decent sized lug.

Have you got a pic or videos of the pump in action?
I could do with something to end the digging, have a hip problem.

Thanks
User avatar
kieran
Site Admin/Owner
 
Posts: 2511
Images: 19
Joined: Wed Jan 15, 2003 11:27 pm
Location: Mayo, Ireland
Has thanked: 259 times
Have thanks: 445 times
Blog: View Blog (3)

Re: Pumping lug

Postby Thompst111 » Fri Nov 08, 2019 1:18 pm

I dont as me mate made it. I'll try to put some up but we got the idea after seeing a you tube video. Just type it in on you tube and there's loads of videos how to make one
Thompst111
SAI Bait Ball
 
Posts: 108
Joined: Fri Jan 04, 2019 10:12 pm
Has thanked: 4 times
Have thanks: 18 times

Re: Pumping lug

Postby cd07 » Fri Nov 08, 2019 1:20 pm

I've sent Kieran a PM

For this message the author cd07 has received thanks:
kieran (Fri Nov 08, 2019 3:55 pm)
User avatar
cd07
SAI Hammerhead
 
Posts: 321
Joined: Mon Sep 24, 2007 8:26 pm
Location: Balbriggan
Has thanked: 1 time
Have thanks: 79 times

Re: Pumping lug

Postby kieran » Thu Nov 14, 2019 3:27 pm

Been down to the local plumbing supply and purchased all the materials required. Just under € 20. Will post here to illustrate how sh*te my DIY skills are in due course! ;0)
User avatar
kieran
Site Admin/Owner
 
Posts: 2511
Images: 19
Joined: Wed Jan 15, 2003 11:27 pm
Location: Mayo, Ireland
Has thanked: 259 times
Have thanks: 445 times
Blog: View Blog (3)

Re: Pumping lug

Postby cd07 » Thu Nov 14, 2019 4:05 pm

Good luck Kieran!
User avatar
cd07
SAI Hammerhead
 
Posts: 321
Joined: Mon Sep 24, 2007 8:26 pm
Location: Balbriggan
Has thanked: 1 time
Have thanks: 79 times

Re: Pumping lug

Postby Vladimir » Fri Nov 15, 2019 5:34 pm

I tried a few times in Seafield, Co Clare (Close to Spanish Point). Works great but digging keep you warm in this weather :)
Nice video here explaining how it works

http://youtube.com/watch?v=lljW9ln8S1c
Vladimir
SAI Lug Worm
 
Posts: 18
Joined: Tue Sep 03, 2019 4:44 pm
Location: Limerick
Has thanked: 8 times
Have thanks: 28 times

Re: Pumping lug

Postby kieran » Sat Nov 16, 2019 12:21 am

Well, it's complete and it is definitely not a thing of beauty!

Weather permitting it will get a testing tomorrow at low tide.

Made it form 1.25 inch PVC, 1 metre pipe, slotted into T section, small section for a handle, with a cap end on the top of the T.
Glued together with PVC glue. Put a 8 mil washer on the drilled cap end as the bar would doubtless eat the PVC otherwise.

Two nuts and two threaded nuts or end nuts and you are done...

Silicone proved to be completely hard and the tube is the wrong diameter. Was searching around and found a grey plastic door stop, complete with 6 mil hole. Damn thing was tapered slightly but put it into the drill (on an 8 mil bolt) to create a lathe and some judicious filing and sandpapering later, its a snug fit. Might try some washing up liquid in the tube. Might not be as good as silicone.

Word of warning for people - don't glue in the end cap. The only potential flaw will be a lack of suction created in the pump / pipe, so if you need to replace the doorstop with a silicone block, you will need to have access to it.

I will put the photos up.... but only if the damn thing works! Total build cost was about €20 including the glue (€ 6).

I have lots of sandy beaches with no stones hence willing to try the PVC option...

And I have a fat trap that needs to be repaired (ugh!)...

More anon.
User avatar
kieran
Site Admin/Owner
 
Posts: 2511
Images: 19
Joined: Wed Jan 15, 2003 11:27 pm
Location: Mayo, Ireland
Has thanked: 259 times
Have thanks: 445 times
Blog: View Blog (3)

Re: Pumping lug

Postby cd07 » Sat Nov 16, 2019 1:33 pm

You went the pvc route! I toyed with the idea myself. If your doorstop fails. I've also used rig winders cut to size with a hole cutting drill bit. Works quite well
User avatar
cd07
SAI Hammerhead
 
Posts: 321
Joined: Mon Sep 24, 2007 8:26 pm
Location: Balbriggan
Has thanked: 1 time
Have thanks: 79 times

Re: Pumping lug

Postby kieran » Sat Nov 16, 2019 3:01 pm

First test - doorstop is too tight a fit, works fine coming up, but pushing it back down is a disaster. Could be in the gym.... adjusting it.
User avatar
kieran
Site Admin/Owner
 
Posts: 2511
Images: 19
Joined: Wed Jan 15, 2003 11:27 pm
Location: Mayo, Ireland
Has thanked: 259 times
Have thanks: 445 times
Blog: View Blog (3)

Re: Pumping lug

Postby cd07 » Sat Nov 16, 2019 3:05 pm

Lash the fairy liquid in that'll help!
User avatar
cd07
SAI Hammerhead
 
Posts: 321
Joined: Mon Sep 24, 2007 8:26 pm
Location: Balbriggan
Has thanked: 1 time
Have thanks: 79 times

Re: Pumping lug

Postby kieran » Sun Nov 17, 2019 8:17 pm

A bit concerned that the sand will be too abrasive on the PVC and that ultimately I will have to go with a metal version, but such is life.
Doorstop has been 'lathed' a fraction thinner again. May have to look at suction rings. 2nd test later in the week, weather permitting.
Again will post pictures provided I can get this version to work...
User avatar
kieran
Site Admin/Owner
 
Posts: 2511
Images: 19
Joined: Wed Jan 15, 2003 11:27 pm
Location: Mayo, Ireland
Has thanked: 259 times
Have thanks: 445 times
Blog: View Blog (3)

Re: Pumping lug

Postby Vladimir » Mon Nov 18, 2019 10:17 am

Guys, has anyone one noticed that some of the worms especially blow lugs can be damaged through process most likely due to the pressure and the last thing I would do it is to put a damaged one with the good ones... Wondering how can this be avoided? different angle or more gentle pushing?
I tried this only once, so this is the concern I got after using. BTW works great for rags.
Vladimir
SAI Lug Worm
 
Posts: 18
Joined: Tue Sep 03, 2019 4:44 pm
Location: Limerick
Has thanked: 8 times
Have thanks: 28 times

Re: Pumping lug

Postby corkconian » Wed Nov 20, 2019 3:38 am

Im no expert in pumping by any means but you should be able to reduce the suction pressure using the wingnut on bottom. I find the pressure does burst the blow lug so reducing it works better.

For this message the author corkconian has received thanks:
kieran (Wed Nov 20, 2019 12:58 pm)
User avatar
corkconian
SAI Bait Ball
 
Posts: 166
Joined: Thu Jan 14, 2016 1:36 pm
Location: Limerick,Cork,Kerry
Has thanked: 7 times
Have thanks: 130 times

Re: Pumping lug

Postby kieran » Mon Mar 30, 2020 11:09 pm

Cripes but the old threaded bar rusts damn fast!
I have taken out the doorstop and replaced it with a flat plastic disc cut from the top of a bucket.
Did a job on the other end too, replacing a nasty square lump of wood with a more ergonomic handle - the wood with chucks shaved off and sanded so that it fits nicely in the hand.
Looks far better, no idea if it will work. Well past 2 K to the nearest lug beds, so I guess testing of it will have to wait.

...

If this keeps up, I may have to do something in the house or garden! :shock: stay safe people
User avatar
kieran
Site Admin/Owner
 
Posts: 2511
Images: 19
Joined: Wed Jan 15, 2003 11:27 pm
Location: Mayo, Ireland
Has thanked: 259 times
Have thanks: 445 times
Blog: View Blog (3)

Re: Pumping lug

Postby cd07 » Mon Mar 30, 2020 11:19 pm

Haven't checked mine I'm sure its probably the same! This staying indoors is a f'n nightmare
User avatar
cd07
SAI Hammerhead
 
Posts: 321
Joined: Mon Sep 24, 2007 8:26 pm
Location: Balbriggan
Has thanked: 1 time
Have thanks: 79 times

Re: Pumping lug

Postby eoghanb » Mon May 18, 2020 11:16 pm

A bit of rubber foam mat works great ,just put a big washer either side of the piece of mat and use a wingnut to adjust the suction ,if you tighten the nut it squeezes the mat and increases the width of the mat .
User avatar
eoghanb
SAI Sea Dog!
 
Posts: 901
Joined: Sun Apr 17, 2011 10:34 pm
Location: balbriggan co.dublin
Has thanked: 17 times
Have thanks: 336 times


Return to Shore Angling Q&A / Forum

Who is online

Users browsing this forum: Google [Bot] and 35 guests

cron